Home > Products > Wall Sconces > travertine fluted glass wall sconce
travertine fluted glass wall sconce
  • travertine fluted glass wall sconcetravertine fluted glass wall sconce

travertine fluted glass wall sconce

    A travertine wall sconce with a fluted glass cylinder shade on an antique brass arm. 305 mm tall, E14 socket, hardwired. Made by Strong Lighting.

    Model:STB16114-1

    Send Inquiry

    Product Description


    A single fluted glass cylinder. A collar of yellow travertine. One brass arm curving back to the wall. The STB16114-1 does very little on purpose, which is why it holds a corridor at eye level where most wall lights start to look like hardware.

    This travertine fluted glass wall sconce belongs to the 16114 family, a series built around two materials that currently define high-end interiors: open-pored natural stone and reeded glass. Both are doing the same job from different directions. The stone gives the fixture weight and warmth; the glass breaks the lamp into vertical bands so the light arrives soft rather than as a bright point. Specify it in pairs along a hallway, single beside a bed, or in a run through a hotel corridor.


    Why Yellow Travertine, and Why It Reads Expensive


    Travertine has moved from bathroom walls to lighting, and for a clear reason: it is the one stone that looks warm without being decorative. Yellow travertine — the honey-cream variety quarried in Turkey and Iran — carries horizontal banding and open pores that catch light differently across the surface, so the material stays legible even in a small component.

    On this sconce the travertine appears twice: as a collar at the base of the glass cylinder, and as the stone seating the arm. It is a small amount of stone, maybe forty millimetres of height, and it changes the whole read of the fixture. Without it the sconce is a metal bracket with a glass tube. With it, the diffuser has a footing, and the piece belongs to the same material language as the plaster, the limestone floor and the oak joinery around it.


    Strong Lighting uses solid natural travertine, cut and cored, then honed to a matte surface. It is not a cast composite and not a printed wrap. Banding, pore density and tone shift from piece to piece, and we do not standardise that variation away — it is the detail that survives close inspection in a showroom, and the reason a matched pair should be requested at quotation stage rather than sorted afterwards.


    Fluted Glass, So the Eye Reads Light and Not a Bulb


    On this travertine fluted glass wall sconce the shade is pressed fluted glass: deep vertical reeds running the full height of the cylinder. A clear E14 lamp inside is refracted into vertical bands instead of escaping as a single bright point, so from a metre away you read a glowing ribbed column rather than a bulb behind clear glass.


    This is the practical answer to the oldest complaint about glass wall lights — glare at sitting height. Reeded glass softens the filament into a vertical pattern that is comfortable to pass close to, which matters in a corridor or beside a bed. It also keeps the sconce looking considered when it is switched off, because the texture, not the lamp, becomes the subject.


    Antique Brass and the 305 mm Proportion


    The arm and backplate are iron with an antique brass finish: warm brown-gold rather than bright yellow, closer to an aged instrument than to polished chrome. It sits naturally against oak, walnut, travertine and lime plaster, which is where most of this series ends up.


    The proportions are deliberate. At L125 × W100 × H305 mm, the 125 mm projection clears a 1.0–1.2 m corridor without catching a shoulder, and 305 mm of height sits above a chair rail without competing with a picture. Mount with the shade centre at 1.75–1.85 m along a hallway, 1.40–1.50 m beside a bed, or around 1.90 m on a staircase wall following the rake of the treads.


    If the project is coastal, or the sconce is going into a humid interior, tell us at quotation stage. Plating specification is confirmed per order, and we will advise on the right finish rather than let a brass fixture haze in its first season.


    Where This Sconce Works Best


    Entrance halls and corridor runs. Mount this travertine fluted glass wall sconce in pairs 2.4–3.0 m apart, on the same circuit as the ceiling downlights, so the wall stays legible when the room is dimmed.


    Bedside. One sconce per side replaces a table lamp and frees the nightstand. The 125 mm projection keeps it clear of a reading position, and the fluted glass keeps the lamp out of a sleeper's eyeline.


    Staircase walls. Follow the treads at about 1.90 m. The vertical cylinder echoes the rise of the stair, which is why the fixture photographs better on a staircase than almost anywhere else.


    Hotel corridors and boutique guest rooms. The travertine collar survives constant close inspection, and the fixture is small enough to repeat at scale without a project looking over-lit.


    Restaurant banquettes and powder rooms. Mounted at 1.30–1.40 m between tables, or in pairs either side of a mirror on a dimmer.


    Specifications


    Model: STB16114-1


    Fixture type: Single wall sconce, uplight


    Shade: Pressed fluted glass cylinder


    Stone: Natural yellow travertine collar, honed


    Frame: Iron, antique brass finish (STB)


    Overall dimensions: L125 × W100 × H305 mm


    Lamp holder: E14, max 40 W (lamp not included)


    Voltage: 220–240 V 50 Hz (110 V on request)


    Installation: Hardwired to standard round wall box, no integral switch


    IP rating: IP20, dry interior locations


    Packing: 1 pc per carton, 17 × 10 × 24 cm, 0.0041 m³


    Lead time: About 45 days after deposit


    Certification: Lamp holder and wiring to CE / VDE requirements


    Customisation: Finish, arm projection, stone selection, private-label packing


    Built for Export, Not Just for Photographs


    Glass and stone are the two components most likely to arrive damaged, so this sconce is packed with the cylinder sleeved and the travertine collar cradled separately, one piece per carton.


    For project buyers working with Strong Lighting, the practical points are consistent 220–240 V wiring, lamp holders to CE and VDE requirements, a repeatable antique brass finish across batches, and a 45-day production window that can be planned against a container schedule. The factory has been manufacturing in Guzhen, Zhongshan since 2015, with two production lines, an 800 m² showroom and three in-house designers — enough capacity for container orders, small enough to answer a custom request in days rather than quarters.


    OEM and ODM work is standard rather than exceptional: change the metal finish, adjust the arm projection, select stone from a single block for a batch, or brand the carton. If you are building a private-label travertine lighting programme, this sconce is a sensible entry point because the form is simple, the stone cost is controlled, and it photographs well at every price tier.


    Frequently Asked Questions


    Q1: Is the travertine natural or a composite?

    It is solid natural yellow travertine, cut and cored, then honed to a matte finish. It is not cast, printed or resin-filled to look like stone. Banding, pore density and tone vary between pieces — a characteristic of the material, not a defect. For matched pairs, tell us at quotation stage and we will select from the same block where stock allows.


    Q2: Does the sconce have a switch on the fixture?

    No. It is hardwired and controlled by the room switch or dimmer. It mounts on a standard round wall box with concealed fixings so the backplate sits flush against plaster or panelling.


    Q3: Can it be mounted upside down or horizontally?

    It is designed for vertical uplight only. The travertine collar sits at the base of the glass and the lamp holder at the bottom, so rotating the fixture would put stone above the light and break the silhouette. For a downlight version, ask us — the arm can be reworked at production.


    Q4: Is it dimmable, and which lamp should I specify?

    Dimming depends on the lamp and the wall dimmer, not the fixture. Fit a dimmable E14 LED and a compatible trailing-edge dimmer for smooth control. For the look this sconce is drawn for, use a 4–6 W dimmable LED filament lamp at 2700 K with CRI 90 or above. A frosted lamp softens the reed pattern into an even glow; a clear filament lamp gives sharper vertical streaks.


    Q5: Is it suitable for a bathroom?

    It is IP20, so it suits dry interior areas — hallways, bedrooms, dining rooms, powder rooms outside the splash zone. Inside a shower enclosure or directly over a bath you need an IP44 fixture, and we would rather say so than sell you the wrong one.


    Q6: Will a pair match?

    Travertine is quarried, so two collars will never be identical. We select both from one block where stock allows, which brings banding and tone close enough that a symmetric installation reads as a pair. Specify the travertine fluted glass wall sconce as a two-piece order and both collars are cut from the same block, rather than sorted afterwards.


    Q7: What is the minimum order and lead time?

    Strong Lighting runs standard production from 50 pcs per model. Lead time is about 45 days after deposit for standard finishes, longer for custom plating or batch stone selection. OEM and ODM are both available under your own label.


    Lamp Type Wall Scones
    Cod. STB16114-1
    Area Indoor
    Bulb base E14 Max1x40W
    Dimension(MM) L125 W100 H305
    Primary material Iron+marble+Glass
    Finish of metal Brass
    Color of shade Clear
    IP degree IP20
    Item box length(CM) 17
    Item box width(CM) 10
    Item box height(CM) 24


    Related Category
    Send Inquiry
    Please feel free to give your inquiry in the form below. We will reply you in 24 hours.
    X
    We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies. Privacy Policy
    Reject Accept